hi...Pontiac heads
anybody have an idea what 10093328 gm pontiac heads are ,,,??? any good ??:welcome:
View ArticleFloor panel
I have 1987 chevy caprice, My floor panels is rusted badly and I want to replace the panels. I have been searching the internet for replacements, but I had no luck. Do anybody have any suggestion on...
View ArticleAir VS Electric Drill
Does an air drill have any advantages over an electric drill, other than using the air line which might be easily available? Air drills certainly are inexpensive.
View Articlesky lights , best placement
Hello.. I have a modest 1 car garage and the house and garage will be getting a much needed roof, I bought 2)21"x48" sky lights. to help with light on the back end of the garage.. it's 26' long so the...
View ArticleDOT3 vs DOT4
My car manual calls for DOT3 brake fluid, would it be fine if I went with DOT4? All it does it increase boiling point?
View ArticleGone for awhile!
Back to the computer, been working and having a son, takes a ton of time these days. Got a little breathing room and wanted to come back to the forum, so Hello!
View Articlejoek
1990 f250 351w efi, loss of power above 3000 rpm, change fuel filter, could injectors be dirty?
View ArticleWarranties? Gas Tank Issue
I'm posting asking for opinions, a dangerous thing I know. So here it is, I can't build a Rod in 30 minutes like TV. My 39 Plymouth is at 4 years, on the road, but interior not done yet. I bought a...
View ArticleVW 1600 trans adapter
IS there other automaic trans that could adapt to a 1600 other than the vw type 3 trans ?
View Article48 F1 exhaust
My truck has 350 sbc with block hugger headers, I want to put in a dual scavanger exhaust system. I've been looking in the catalogs at the systems, but I have no idea on what to buy. I want to do it...
View ArticleOregon hot rodders???
Just wonderin if any of you fellers are up here in Oregon! Gimme a shout brotheren. By the way I though it would be fun to have a by state section to meet other Rodders in your state.
View Article350 TBI first time rebuilding engine...question
Hi:D How you doing guys? I decide to rebuild my 350 TBI engine for 1993 In real... I jut need your help friends:rolleyes: I took a stuck engine and want to turn it to performance engine I over size the...
View ArticleIntake Leak Into Lifter Valley???
Manifold has been off a few times, and every time, the gasket "crush" appears to be all around. But I'm consistently oil fouling the same three plugs. Clean them and again, the same three! Engine runs...
View ArticleVacuum Question
I have a small block Chevy with a demon carb. I Have the vacuum tank hose, trans modulator hose and brake booster hose going to a connector screwed into the back of the manifold. Idle is a little...
View ArticleWhat's really inside that dome on top of a 747?
What's really inside that hump on the top of a 747? Mere peasants like myself wouldn't get a chance to get close to even find out. Discuss.
View Article5.3 Cam upgrade
Hi im doing a 5.3 swap with 4l60 in my 77 camaro. Wanted to do a cam upgrade while the engine is out, so wondering some recomendations on a cam. Will be keeping all factory fuel injection and intake....
View ArticleHelp on a neutral safety switch
Howdy: I'm wiring my 69 Chevy truck (93 GM 350 TBI/700 R4) with a Painless harness which includes wires to connect to a neutral safety switch. I believe one carries in power and the other one passes it...
View ArticleWhy do i get poor gas mileage
:confused:I have a 51 ford f1 with a 302 & aod & the original 3:73 rear I have an old holley 4 bbl on it-right now i am only getting 10-12 mpg I thought that I should be getting better gas...
View Article