CVT Opinions
My wife wants a new car. I have researched some new models that she wants and a couple are only availible with CVT (Continuous Varible Transmission), like the Subaru Outback. *She won't have a manual...
View ArticleT-350 - Intermediate Clutch Stack Clearance
Hey. Is it OK to put another steel under the wavy steel to reduce this clearance? Mine is about maxed out at .110 or so z
View ArticleClik here to view.
T-350 Rebuild Tips
If you have to do this outside .......use a big garbage bag and put the tranny inside......that way it will be protected during the rebuild while you're doing other things. Also, I HIGHLY recommend...
View ArticleCamel hump heads vs vortec heads
Hello to all i got a question for you guys, i want to change the heads on my 1972 327 or its a 350 i got to pull pan but havent got that far yet to verify the motor,if you had a choice to go camel hump...
View ArticleWhat effects does low rpm's have on air fuel mixture?
(preface: 355sbc, 232@.50 480lift cam, decent heads, rpm air gap, holley 650 dp, t5 manual) I put a wideband gauge in my Camaro and I've been having fun fine tuning this carb with it. Got it dialed...
View ArticleWeird Oil Leak
I have a rebuilt SB 350 that I did myself a while back. Was using 20-50W oil and never had a leak. I just changed my oil 2 weeks ago to a little bit thinner oil and now I keep having an oil leak...
View ArticleTicking noise (Videos Inside)
My built 350 SBC, has developed a ticking noise. Here is a video with the motor running, it's idleing low here, it hasn't warmed up. But you can here the ticking. Engine On - YouTube Engine On -...
View ArticleFuture project
In the future, I'd like to build something in a older hotrod, 30's or 40's. If I do, I'd like to use the 434 sbc out of my chevelle with a 6-71 on top of it. I'd stick a mild sb in it for a driver. I'd...
View ArticleArt Malone died this morning
I just got an E-Mail from "Big Daddy" that art Malone had died at his home this morning at 6:00 am. This was the last result from a high speed boat crash he was in a few years ago. Bob
View Articlerear suspension in a model a
What would give the better ride buggy spring with shocks or coil overs ? Also would panhard bar be required with both types ?
View ArticleClik here to view.
first of 62 chev painted
I got the first parts of the 62 chev painted yesterday. Victory red and three coats of SPI Production clear with a sand with 1500 and buff. Attached Thumbnails
View Articleneed help in using a magnetic mount caster/camber gauge
help, i just picked up a intercomp magnetic mount caster camber gauge can somebody assist me in going through the proper procedure in using this tool for aligning my front end, using a stock MII...
View ArticleClik here to view.
Chopped,Stretched And Widened 33 Willy's
A few pics of my latest 33 Willy's custom roller we built, Other than the grill this one is finished and heading to it's new owner in Cal. to be finished. Scott Attached Thumbnails
View Article1998 gm z-71 5.7
I wrote in a while back about the problem that started after I installed a new cap , rotor & plug wires. The truck runs great except it will skip a beat while drivind down the road at just about...
View ArticleDemon carbs lean at transition
I got my AEM Failsafe hooked up and it works great. Easy to read display even in sunlight. Anyway, have some questions: I am running a 6-71 blower with 2 Demon 650 double pumper blower carbs. Idle AFR...
View Article1936 ford 1.5 ton
I have purchased a 1936 Ford 1.5 ton truck,Would like to know if anyone can tell me what frame or subframe to use?(Goal is to keep dually rear end),Thanks for any info.
View Article4l60e no reverse
I got a 96 sonoma 4.3l vortec and it has no reverse. I have rebuilt a 91 700R4 but i dont think the 4l60e needs rebuilt. The truck pulls great in every gear buy reverse nothing rpms go high nothing. I...
View Article