Hello
Hello hotrod fans . I am from Bulgaria. I hope to learn from you many new things about hotrods. Last year I started to build mini hot rod for my son. Soon I will post some photos.
View ArticleTBI fuel delivery problem when starting
I am resto-moding a 69 C10 using a GM 350 TBI engine/700R4 setup. I wired the truck with Painless harnesses including the TBI harness. My problem is starting. It turns over fine, and if I prime the...
View ArticleEngine Bearings Failure (again) BBC 555CI, OFFROAD
Hello , i have a edelbrock/musi 555 697hp engine, its a Big Block Chevy with DART BIG-M BLOCK, i have a problem with it, it keep failing main bearings, it's the third time in less than 3k Miles, i use...
View ArticleClik here to view.
No brakes and peddle is solid
I have a mud truck that has no rear brakes, just front. I have the rear blocked off with a plug and the front is bleed and hooked up. It is a 94 s10 blazer master cylinder with 80's 3/4 ton front...
View Articleengine noise, help !
my freind's 2005 Chev truck, I assume 350, engine makes a ' wierd sound. kinda like chirpping, or like a combination of a click, chirp and a squeak. (please bear with me here ) sounds like comes from...
View Article355 first timer
I recently built my first motor. With the help of an experienced friend. Of course I made a few bad choices 2 years ago when I began it on a budget but I'm just now cranking it up. It's a 355 with dish...
View ArticleClik here to view.
Thank you Dale Jr.
Great gesture from Hendrick Motorsports to carry this special decal on all four cars, including Dale Jr.'s No. 88 National Guard Chevrolet, at Kansas Speedway.
View Article2001 GMC SAFARI P0304 False Missfire
I have a 2001 GMC Safari van with P0304 code. I cannot feel a missfire, the engine runs great but the scanner missfire counter picks it up at 1500 rpms and up. The check engine light flashes at that...
View Article1933 chev master coup
The inside of this car body is basically wood framed. I am working on the front door hinge posts. I have removed all the old rotted wood and have taken the hinges and door off too. Now is the part I...
View ArticleMini Hot Rod
Here is some photos of my project for my son. What do you think? The car is with petrol engine 2 hp from chainsaw, disk brakes from bicycle, front weels are 10 inch and rear wheels are 13 inch. Message...
View ArticleWhat else is needed to Hook clutch pedal to Transmission
I am not running a Hydraulic set up, the question is for mechanical clutch linkage set up. I have a 1980 Z28 Camaro, the owner before me converted the car from (factory) manual to a Th400 Automatic. I...
View Article383 wont idel blow 2000
hello to every one I have a brand new 383 strocker that I can not get to idel below 2000 rpm. it has a comp cam with .454 gross lift and msd ing. and msd efi. I have checked for vacume leaks and found...
View Articlecrimp terminals for a 1949 dodge
The wiring under the dash of my 49 coronet is a mess, some of its burned up so I'm in the middle of replacing it. I cant seem to find any kind of connector for the switches (headlights, dimmers, wiper)...
View ArticleShifterknobs is my life!
Hello! My name is Gustav, but I am more known (in various subcultures) by the name GugerArt. I'm a freelancing illustrator / designer from Sweden, but lately I've fooled around in the world of...
View ArticleSupercharged WOT AFR
What should the AFR read at wide open thottle on a pump gasoline roots blower application? I am hearing everywhere from 11.0-12.5 and that is a pretty broad range. My car is at 12.7 and don't know how...
View ArticleClik here to view.
Custom paint tricks 101
After a lengthy discussion in another thread about a paint technique, someone suggested a thread dealing with the way some custom paint tricks are done. I was "volunteered" to start it... and since I...
View ArticleVacuum/boost gauge on roots
Is there a vacuum circuit you can make with a one way valve and Tee, to get accurate vacuum readings along with boost? I want to get rid of the separate gauges. I did a search, did not find much. If...
View ArticleLean/Bog when initially stepping on gas
Hi, I have a bog (A/F gauge shows very lean) condition when first step on the gas then all is fine all the way to WOT. I especially notice this when leaving a stop sign/light or cruising at 30 mph in...
View Article425 Caddy into a Stroker 454
I did this "thread" on "www.500CID.com" a few years ago, & it's "archived" on "www.cadillacpower.com". The 425 Cadillac engine is "only" @ 40 lbs. heavier than a stock sbc. The heads are a bit...
View ArticleLocked Timing
I've had several say I need to lock my timing and get rid of vac advance. I don't want a starting problem, kick back. I have a 434 sbc in my chevelle, dart block and 230 heads, with a 640 lift bullet...
View Article