Clik here to view.
new here, comments on car please
Hi everyone, new to the forum and just pulled this car home tonight. Actually found it in a field off a 2 lane road. I was wondering if anyone may recognize it. It has very distinct purple firewall and...
View Articleflexplate bell housing shield
Has anyone installed a flex plate shield on a 78 to 83 G body with stock firewall? I'd like to see some pictures.
View ArticleHead gasket seepage???
I was contemplating getting a car that is supposed to have a dry sump 421 engine and the owner informed me today that he noticed a little coolant seepage where the heads meet the block. He said that...
View ArticleTremec tr-6060 on BMW
Hi, this is my second post here regarding my setup, and hope that you help me here again :) AGAIN Small intro about my BMW engine for people who are not familer with BMW engines: Engine : m50b25 (2.5L)...
View ArticleBig block or ls
So ive been doing some resarch on an ls swap in my truck and a buddy of mine said dont waste the time or money just go big block simpler and proven. I want fuel injection either way and reliabilly is a...
View ArticleCam for SBC 355
Hello everyone, I need some help with cam selection for 1975 SBC 355, stock heads (ported and polished), Edelbrock 2701 Performer EPS intake, Edelbrock Thunder Series AVS 650 carb with vacuum...
View Articlegoodbye cruel world!
i was going to kill myself by taking 100 pain pills. but after the second one i felt better! :D
View ArticleMopar 360 in Model A?
Can you point out any pictures or journals where it can be seen how Mopar 360 engine would fit to Ford Model A, and what needs to be modified? Thanks.
View ArticleAnyone making big power with Cheap EFI setup
Anyone making big power with Cheap EFI setup? I am thinking megasquirt or something similar. But havent been able to find anyone actually using them to make good power with out FI. I want to focus on...
View ArticleMax cam lift for a 350 chevy stock head?
Hi anyone know what is the maximum cam lift for a stock chevy 350 cylinder head? My 350 is from a camaro 76. I got a roller cam with .539 ex lift with 1.5 rockers. Can I use it with a good set of valve...
View Articlepower steering leaks
I just got done installing new lines on my Mustang 2 rack and GM pump. I sprung a leak at the rack. The fittings have those o rings on them. Did I over tighten them? Is there anything better than those...
View ArticleWho has the best prices on the Sata Spray Guns???
I want to buy a new sata 4000b hvlp 1.4 tip. Who has the best prices? I was going to contact spray gun world, but I am still reading reports from consumers that they never received their paint guns...
View ArticleNewly Built 383 Engine Vibration. Did i pick the wrong flywheel?
Just had built a 383 stroker GM 1 piece rear main seal block Eagle Rotating assembly kit (4.030X3.750 5.7 Rod, -18CC inverted dome) PN: Eagle B13004L Eagle Street and Strip Rotating Assembly The kit...
View ArticleThe Genius of GM!
Now there is going to be an electric Cadillac? Sheesh! Didn't GM learn ANYTHING from such genius moves as the Cimmaron and the Catera? Against a background where it appears that Renault/Nissan is...
View ArticleClik here to view.
Free live video from the 2012 california hot rod reunion this weekend!
Hosted by BangShift.com
View ArticleVortec Heads with 292h Comp Cam
Has Any Body Ran A Comp Cam 292H (501/501)lift, with Vortec Heads 64cc, If so how did it perform on the Street, and did you have any problems running the set up?
View ArticleWhich Posi?
Does anybody know if a posi rear out a cop caprice will fit my delta 88? I think it should cause they both b bodies, but just checking.
View ArticleClik here to view.
Heavy duty vs Regular Duty
I just don't know which spring will be best. These two springs are out of a 4L60E Superior Shift Reprogramming Kit. (see pictures) Heavy Duty and Regular Duty is all the info I have. Can anyone give me...
View Articlesbc 406 hp torque?
im building a 406 sbc with 1997 vortec heads 092 casting they have been ported and polished on a bench flow they have 202 160 valves screw in studes guide plates 64 cc combustion chambers. it will have...
View ArticleHow Low To Go?
What is considered a safe height measuring ground to lowest point on the front crossmember? I want to drop my coupe some more, but if I use 2" dropped spindles, my clearance will be 4" to the ground....
View Article