new blood!!!!
Hello everyone. I hope to be a value to this site and will post pics of the ride soon:D
View Articleedelbrock performer
hello, i have a edelbrock performer manifold on a 305 sbc,, my question is there is only 1 vacuum port on the back of the manifold,can i use a tee fitting to run the vacuum line from the brake booster...
View ArticleEdelbrock advice?
Is there any way an Edelbrock carb can cause intermittent pinging? My stroked 351W has pinged on and off for some time. I've had the distributor apart (MSD billet), tried running with vacuum plugged,...
View ArticleTH350 problem.
Hi, apart from my Carb acting up my trans is also not working properly. It started about 2 years ago, the reverse wouldn't engage until i revved the engine a bit, wich got it to engage and spin the...
View ArticleClik here to view.
Under floor master cylinder
Hello. I have a power brake master cylinder mounted under the floor. Mine is mounted backwards as I think most are. Both reservoir are the same size. I am running disc's in front and drums in rear....
View Articleifs for 1957 hev pickup
im changing my 57 hev pikup to a ifs kit .im planing on coil overs, power rack and a swaybar not sure whih one is the easyest and best built .and sugestions . also not sure which would ride best a new...
View ArticleItalmeccanica supercharger
Hello, Ive tried to do a little research on a supercharger I have found. All I really know about it, is its a Italmeccanica supercharger with 1 carb and the intake is for a flathead v-8. I guess it was...
View ArticleClik here to view.
can brake pads go infront of the axle
i have a 50 ford shoe box its choped, has a 86 buick grand national front end the rear is from a 2000 ford explorer i put in coil overs in the rear and the rear end was narrowed i went to put the...
View ArticlePcv hook up
Ok so I'm trying to clean up my engine bay a little bit and I was wondering, instead of having the pcv valve hooked up to the port on the carb, could I hook it up to the fitting that sits on the back...
View Articlewhy is it that i need to hold down the gas pedal to start my engine
350 chevy, 600 cfm edelbrock 1405 carb, xe 274h comp cam, performer eps manifold, one inch open spacer, short tube headers is it the carb spacer ? could i be running rich ?
View ArticleOffset Brake Pedal Pad
:confused: I have a slight problem with the brake pedal in my deuce. Before the car went to the upholsterer there was no problem with the clearance with the pedal pad, steering column and my foot....
View ArticleNewbie...
Whats up guys. I'm new to this whole forum community. Just learning how this all works. I have a 89 GMC s15 and now I have a 366 big block. i know that people say its junk but I'm not trying to build a...
View ArticleHello all
Hi. I'm joining the forum because I just acquired a 49 Chevy 3100. It has a 70 Corvette 454 (modified) , a Turbo400 with his/her shifter, and a Ford 9". Body is pretty good, floor pans not so good....
View ArticleA great site on TV Tommy Ivo full of photos.
TwinBuick Some great photos of the chassis and engines.:thumbup: Brian
View ArticleDegree'n a cam parts
Hello.. So I have the comp cams degree kit, used it many times, with flat tappet cams, easy just bought a single solid lifter and good to go.. well this engine that I'll be stab'n a cam in is a g.m....
View ArticleSBC rough idle and running
I have a 1988 350 SBC that ran great on the way to work today, started it at lunch got rough idle and rough while accelerating. Does it with the engine cold and at running temp. Plugs look good, choke...
View Articleupgraded gears for V-8 saginaw 4 speed
Does anyone out there know where I can get an upgraded(strengthened) gears for the saginaw four speed for the V-8's. I heard on one of these threads they were available but saginaw replacement parts...
View Article2013 Spring Throwdown In T Town Live Streaming
Its springtime, and that means the baddest group of Pro Mods, Outlaw 10.5s, and more are on their way to Tulsa Raceway Park for the 2013 $50k Throw Down in T-Town which starts Friday at 5:30PM Central...
View ArticleWhat oil you runnin?
Got a solid flat tappet cam in the s10, Been reading but it's getting me nowhere. Some say this, some say that. Can I run Delo 400 le with a bottle of engine break in additive? Anyone recommend one...
View Article