FNG from meridian Idaho.
Hey everybody! New guy here from Idaho who lives and breathes rods, customs and old American iron in general.
View Article400 SBC, do i need bigger camshaft ?
Engine is 1975 model, the block # is 817 and it's 2 bolt block with main studs Heads are # 882 that have been pocket ported and do have 1.94"/1.5" valves. It's been bored 0.030" over and has piston's...
View Article436 sbc
What kinda price should I ask for my 436 carb to pan? It's a dart Motown block, dart 230 heads, bullet mech roller, super victor intake, 850 QF carb. fab type valve covers, ati balancer, 10 1/2 to 1...
View ArticleWhy backup lites blows fuse
I have a 76 f/bird and just discovered the backup lites put a big draw of power on circut when backup and t/signals are on at the same time . It just blew a fuse for the first time today . I don't know...
View ArticleTrans...rearend.
Hello, I have a 1941 ford coupe, I would like to know what it would take to change the stock trans and rearend to a modern one. I would like to leave the flathead in the car. And what brand would work...
View ArticleRearend ????
I am the new guy here. I just purchased a 52 gmc 1/2 ton truck. Has a 235 engine in it. My drive train plan is to keep the motor go with a 350th trans. What rearend should I put in my truck. Its gonna...
View ArticleNV3500 to 5.7 LS1?
Hey guys, this weekend i pulled apart a parts truck I had sitting around(Bought it because the add said 5 speed 350, turned out to be a 305.......) So, I have the 5.7 LS1 from my 2000 Camaro Z28...
View Article406 sbc oil ring side clearance
Hey guys, ive searched all over and cant find an answer so i figured someone on here might know. I have been assembling my 406 small block chevy and am getting ready to put the rings on the pistons, so...
View ArticleClik here to view.
HELP got dirt?in paint how to clean after wet sand&with what
So I just did the muscle car for a fella wanted it done in that blitz black.Well after I blocked the car I sprayed it off with air then cleaned it with scotts shop towels&water(I used w&g...
View ArticleCylinder head cleaning
Can I use a wire wheel brush to clean the head gasket surface and the valve bowls on my cast iron 781 heads? All surfaces of the head? Then power wash and then blow excess water off w/ air compressor.
View ArticleTemp fan probe location.
I have put the adjustable temp. fan switch probe in top of the radiator. The cooling fan kicks inn way too early, so I have probably done a mistake? It's not possible to remove the probe without...
View ArticleOpen 9-Inch
I was talking with a gentlemen yesterday, and he told me something and I wanted to asked had anyone heard this also or tried it. He said a simple way to make a open 9-inch rear positive traction if you...
View Articlesteel
where do you guys get the super high polished stainless steel for engine compartments i live in NJ anyone?
View ArticleJust pure frustration at this point..
Ok guys..just looking for some advice or insight. Either one at this point can't hurt lol. 2 questions..first one is, I am finding condensation under the valve covers and on the rockers and stud...
View Articlebolt in crossmember for a 47 chevy coupe
It has been a while since Ive been on here. I started back to work on my 47 fleetmaster. Finally decided to install a mustang 2 suspension kit. After many heated discussions between all my friends on...
View ArticleNew Engine and Trans
Hello All I'm gonna replace the engine and trans in my 41 Dodge Coupe this winter . I'm thinking of going with a 350 with a 700r4 trans. I'm going to stay with GM because I will be pulling out a 302 ....
View ArticleClik here to view.
Can anyone ID these valve covers please?
I cannot find a manufacturer name or part number. I got these used with the Vortec heads from Craigslist a long time ago, I was told they were from a 300HP (?) crate motor. Attached Thumbnails
View Article2nd gen Camaro/Trans am parts
Hey I got a 1977 Camaro that is pretty bruised up on the front, killer deal on a 78-81 entire front clip. Can i sap these parts out on my camaro if I sap out both fenders and the entire nose? and then...
View ArticleI need some help please sbc lovers......
Hello everyone I need some help and Im hoping someone out there with sum engine knowledge can help me. I bought a 86 buick regal two years ago and it had a 307 olds motor in it. after the motor blew i...
View Article