Newb
Hi all. Been a lurker here for a while. I see a deep well of knowledge on this board, decided to join. Looking forward to some good threads and hopefully contributing to some of those.:thumbup:
View ArticleGM Fuel Tank
1992 Chevy Silverado. Removed the bed and the fuel pump to inspect inside the tank with the idea of cleaning it out since the truck sat two years. In the tank there are baffles that sit quite a ways...
View Article12 bolt truck build?
Hi guys im new to the forum I was just wondering how challenging it is build a 12 bolt truck rear end I have a full spool c clip elemanators and moser axles with some 4.56 gears also what tools will I...
View ArticleOVERDRIVE mp122 blower
Hi all, I'v got a maggie mp122 roots blower, bought this as a kit from edelbrock. The kit came with a ~7.4" bottom pulley & a 3.6" top pulley. On my 388sbc this only delivered about 3lbs boost. I...
View ArticleTrying to Figure out Rear Gears
Hi all, Just trying to figure out my rear gears. When I lift 1 rear tyre of the ground I can spin it easy, open diff right?!? When I lift both wheels off the ground they both spin in the same...
View Article34 Ford Paint Job
How much paint should it take to spray a 34 Ford with fenders. Using Basecoat clear coat . Doing 2 tone. Victory Red above style line, Silver Ice Metalic on bottom. Thinking about single stage on...
View Articlegetting rid of my posi?
Hey. im gettin a 8.8 inch rear end and for my v8 trike i actually dont need a posi! If i dont need a posi is it a big deal to undo? Id like to narrow it about 8-10 inches while im at it but getting it...
View ArticleDowns body door hinges ?
My buddy has an older Downs bodied 32 Ford Sedan with broken door hinges. He called them about replacements but no answer yet. He says they are aluminum. Thats a first for me. Would anyone happen to...
View Articlerunning rich
i just installed a new carb and a new fuel pump,, now i am running rich,, you can smell it and you can tell by your eyes i have tried to adjust the carb,, the floats, air screw, and i messed with...
View ArticleSinclair Gas Station converted into bachelor pad
I got a kick out of this, so I figured I'd share. Bachelor Pad Gas Station - Imgur
View ArticleClik here to view.
need help with a motor swap on a john deere
OK i got a 1986 John Deere 130 last week for free it has a bad motor on it i would like to swap it but not sure what i could put on it here is the spec for the motor that is on it now Engine Type:...
View ArticleClik here to view.
Holley Hot Rod Reunion
Anyone going to Bowling Green next week,please stop by and say hi. Frank Ousley and I will be there running the Crop Duster F/C and the T/F car. Frank sold the dragster to Jim Murphy,but he will be...
View ArticleNew comer
I'm earl 42 years old, i live in Alabama, had old Mustang my first car was a 1966 mustang 289 4-speed, then a 69 mustang with a 429 pi, now my 12 year old son and i are working on a 1956 Pontiac 2 door...
View ArticleHolley Double Pump on Chev 350
I have a newly built Chev 355 with a Holley Double pump on it. It runs rough intermittently and recently I had the car on the highway so it got really warmed up -- not over 200 degrees -- then it would...
View ArticleFoam -- Open cell vs closed cell?
Hi all. Due to having back problems, I like to add extra lumbar support to my seats. The local fabric store sells sheet foam in various thickness, but it only comes in open cell. Is this OK to use in a...
View ArticleOpinions-Iron Eagles 345 BBC heads??
http://www.dartheads.com/products/ai...aitfile_id/85/
View Articletrans. vaccuum and carb
i recently set a 327 in my chevelle with an rpm air gap and a demon 650 carb.the carb sits right above the part on the back of the intake where the "t" would feed the vacuum lines for the break booster...
View Articlet.p.i problems
hey guys,been off for a month or so with a hip replacement. put in knock sensor and changed gas from Sunoco to shell,and my pinging went away.i am leanind towards the gas change as the fix as I ran two...
View ArticleClik here to view.
Timesheets
It's not easy to use trap speed or ET as a judge of RWHP, at least in my case because I'm not consistent enough with my launch. But I'm still working at it. Here are two separate runs, with shifts that...
View Article