Motor ID number
Hello, I am trying to transfer a title of a 1937 Chevy Master Deluxe. The car was my grandfather's and has been sitting on his property for 30+ years. It's motor and tranny have been pulled out. The...
View Article400ci and loving it
Im restoring my 55 chevy 2dr sedan. I rebuilt a 400 sbc with ARP bolts and a 270 compcams with 462 doublehumps. Airgap intake with 650 holley. Im running a 4spd with 3.08 posi. I love the bottom end...
View ArticlePinion Depth Tool
I am getting ready to put the 8.8 together for my olds cutlass in a couple weeks here. What do you guys think of these tools for measuring the pinion depth? http://www.summitracing.com/parts/rat-10006...
View ArticleLt1
can i use the LT1 reverse flow heads #10128374 on a edelbrock performer rpm intake or do i need a different intake
View Articlec-6 shifting problems
I am working the bugs out of my new T bucket build and cannot get the transmission to shift right. I have a 351 W with a C-6 transmission. It will not shift out of first until about 2500 rpms and will...
View ArticleClik here to view.
Vortec Heater Routing
I want to connect the heater in my 5.7 chevy I have the vortec motor, so I assume I need the bypass. The first photo has various connections marked A thru E. Which is the best way to run the hoses? I...
View ArticleCadilac rolling clip
I have a 2005 cadillac sts rolling front suspension w/ wheels, northstar v8, engine computer, fuse box, steering wheel, transmission, drive shaft, complete rolling rear suspension, gas lines, brake...
View ArticleDo electric choke coils go bad?
Do electric choke coils slowly go bad, or do they die all at once? I removed the coil from the carb and wired it directly to the battery. It took quite a while but eventually it moved, barely. I gave...
View ArticleDoor glass binding about half way up
76 F/bird doorglass /power is binding about the halfway point. Have loosened and lubed all the points of adj. and movement and it still does it . Back at it again now for more . Any Ideas ? Thanks
View ArticleIncreasing P/V Clearance
I need to increase the P/V clearance on our motor for the Sprint car. I'm really looking for ways to do this without changing pistons since they are new. The pistons are JE (SRP) domes and I have...
View ArticleMach 468K Sun Tach installation
I have a '64 E Camino, 327 with a 2004r, that I put a Pertronics Electronic Distributor on and want to install a Mach 468K Sun tach. The tach does not have a wiring diagram nor wires for the install....
View ArticleHead bolt ?
Putting my SBC together and realize that I may or may not have made a mistake. Looking for input to decide if I should redo. Anyways, bolted my vortec EQ heads to the block using a felpro composition...
View ArticleClik here to view.
Seats
I know they look like bomber seats, but they are actually the strangest boat seats I've ever seen. There is a tub that mounts to the back section and under the seat cushion that allows you to store...
View ArticleWhere can I buy this paint?
I'm going to paint my car Matte Metallic Blue. I've searched the web and only found it in rattle cans. Does anybody know where I can buy a larger quantity? Thanks in advance.
View Article98 f150 4.6 8.2 mpg!?
I've had this 98 F150 4.6 for a year now but didn't drive it much. Now that I am driving it I find it gets around 8.2 MPG, mostly city driving but it gets about the same when towing my 3200 lb race car...
View Articlenew rat rodder
Hello, I'm a new member. I have a 1927 model t truck on a home made frame race wat front end and a 9 inch ford rear end with a 302 and 5 speed. Traditional steering no column or steering box. Body...
View Article350 Factory heads Max lift
Hey guys whats the max lift I can get from a factory st of 350 heads 333882 Casting. 1.94 Intake 1.50 Exhaust 76cc
View ArticleClik here to view.
Need power window install help!
This is my first post on the Forum. I just purchased a 1948 Chevy pickup that has been chopped 5" and has no side windows installed. I am trying to figure out how to install power windows. My first...
View ArticleReplacing a headliner...
I have the headliner out, brushed off all of the old crusty foam. I am left with a tacky film on the fiberboard. I will be using Weldwood Landau top headlining spray... Should it be safe to go over the...
View Article