introduction
Hi guys. We are going to become real good friends over the next few months. (hopefully) I have a 63 Conti that i just started restoring. I know just enough about cars to get myself into trouble....
View Article305 issues
hey everyone ,my name is bud and im having some issues with a 305 ,(pre 80's) in my 73 chevy,im heading to enigines to leave post where it belongs ,im so greatful for finding this site today .i have a...
View Article305 mess
i have a 305 that a guy built for a street stock and the only thing i did to it was put new valve seats and springs and retainers on it .it has a 460 lift solid lifter cam ,not sure about duration and...
View Article750 downleg or 650 straight leg on a SBC 350
which carb would run better. 750 DP downleg booster or 650DP with straight leg booster. 350 sbc roller cam, 227@50, .565 lift on 108LSA, vortec heads with 180 intake runner, eddy air gap RPM. 1 3/4 LT...
View ArticleHow to find piston CC? I have measurments
I would like to know how to find what the CC of this dished piston is. Says the dish is 0.080in deep and 3.020in in diameter. Can anyone help me out here? I did try contacting the manufacturer but they...
View Article1971 Camaro Diff ID
Hi all, 1971 Camaro base model. 10 bolt diff. I can not identify the diff. Has a number on the rear N then below 1285542. Passengers side stamp GO26 2 or G026 2. I have tried the internet but can not...
View ArticleMake Your Skin Shine Bright and Look Graceful
Dermpure serum is a blend of some symbolic ingredients which works together to make our skin regain its potency to shine bright and look graceful. Not just from outside, the skin gets its strength at...
View ArticleTbi top end vs ls swap
I've been planning my ls swap for my car but I'm having second thougbts because of costs, plus I need to get the car drivable before summer. So I had the idea of swapping the heads and intake from a...
View ArticleClik here to view.
Inside width of 55 57 chevy at center link?
I'm considering using a power steering kit designed for the 55-57 Chevy on my 37 Buick. 1) Does anyone have a 55-57 Chevy they could measure for me? 2) I'm looking for the distance between the mount...
View ArticleFly Board
anyone seen these things, looks like a blast Flyboard Family Official - YouTube
View Articlehow to straighten side panels
On my '37 ford coupe some of the struts/bars in the side panels that are between the hood and the front fenders are not as straight as they should be. The coupe had a nice paint job when I bought it...
View Articletiming cover
I have a 97 roller cam sbc 4 bolt motor, i will soon start building, it nas the plastic cover on the timing chain. it says on it to replace it if removed. why is this. should i get the oe unit or...
View ArticleClik here to view.
Need help with door alignment
Need help with door alignment I've got problems with door alignmnet on my Chevelle. Any suggestions on how to fix this ? Is this something that a body shop could fix...and if so, would it be real...
View ArticleStraight Front Axle sway bar
Has anyone installed a sway bar on a straight front axle in an old pickup? I installed an S10 rear axle on my 36 Chevy pickup and found that I had a roll issue in hard turns, so I am installing the...
View Article1980 gmc 1 ton flywheel
it has 292 but want put early years 283 in it so what flywheel do i use for the v8.. can i use any v8 flywheel on this ? tranny 2 wheel sm456 4 speed with low any help would be grate thanks
View Articlepaint gun help?
i got a matco gravity feed gun i got a few years back. i need to find parts for it! there is no numbers on the gun at all. ive taking it in to a few paint shops with no luck. so i was hoping someone on...
View ArticleLED Flasher fuse
I'm upgrading my tail lights and turn signals to LEDs (I have a 32 roadster with a 350 Chevy). The electronic flasher that I bought must be grounded (no problem there) and the instructions say the...
View ArticleWhat's the correct temperature
I have a 350 crate engine I'm trying to put electric fans. Now I put a cooling fan switch but my question is what temperature should they come on. Thanks for any info I can get all this is in a 85 el...
View Article