Chirstmas Eve.Two firefighters shot and killed
You gun guys have to stop and read this link: Two firefighters shot dead in upstate New York - CNN.com This was a trap.Two firefighters where shot and killed responding to a fire and two others where...
View Article1970 chevelle driveshaft for T-400
hello im looking for some advice before doing anything i have a 70 chevelle ( without drive shaft ) im going to get an old complet 1973 chevy truck with a 454 and th400 ,and swap the engine in the...
View ArticleHemi racing dual spark plug wires
WERE DO THEY GET THE ENDS TO DOUBLE UP THE PLUG WIRES TWO PER CYLINDER DOES ANY ONE SELL THE ENDS TO KAKE THIS SET UP FOR MOTORS? :thumbup:
View Articleneed a glass man Chesapeake VA or NC
Anyone know a good street rod glass man in the Chesapeake VA or North Eastern NC area. Need to install all glass in my 35 Chevy Outlaw car. Thanks, Steve
View ArticleBorg Warner cracked ears
I have a cast iron Borg Warner T 10 that we got cheap with a broken ear. The bottom right. I see a lot of these broken just like the one that I have. I bought a used case that turned out to be a...
View ArticleInput on my 383 setup
I've been reading threads for weeks now, I think I'm close to the set up I'm going with. I'm looking for some input on the final choices to make sure I got it narrowed down to where I need to be. My...
View ArticleClik here to view.
Steering column help..
I have a 67 Camaro with non tilt steering and 4 speed manual tranny. I noticed the blinker arm is not in the right position. Instead of the switch being in the standard 9 o'clock position, it is in the...
View ArticleDelco distributor problem.
I am using a delco window type distributor on a 1961 Studebaker. My dwell is set correctly. When I tried to set the timing, the timing mark fluctuates a half inch or little more. Then I put in another...
View Articledriveshaft concerns
Will the slide yoke that fits in a 94 4l60e work with the nv3500 transmissions from 88-90? Im trying to keep from having to find another yoke.
View ArticleClik here to view.
Santa had some Pro Comp Heads in his bag
I just got set of pro comp heads. These are 59cc with 210cc intake runners. 7/16 studs with guide plates. Also got a set of pro comp head bolts. Pro Comp roller rockers and Stud girdles with extra long...
View Article66 Cyclone seems to sit uneven when measure the heights
I have a 66 Cyclone. When I measure from the ground the left and right wheel wells one side is 1/2 higher then the other. The tiers are the same size, the floor is level, all the supension parts are...
View ArticleCause of Whining Differential?
I'm planning on rebuilding my differential before refitting it to the chassis From what I've read, these differentials have a tendency to whine Since my car was a non-runner when I got it I have no...
View Article850 hp dp question
I was wanting to see if anyone had a similar set-up to see where your carb adjustments were or if anyone had some ball park ideas. The problem is when nailing the gas from a dead stop or rolling and...
View ArticleMax HP for stock 302 block
Just curious what the max HP a stock 302 block will take? One of these days id like to play with a 302 and perhaps throw a turbo on it and some nice heads and see what kind of power I could get out of...
View ArticleDust Cover - Flywheel Cover
Changing the oil filter the other day I cut the back of my hand on the flywheel on my ole Hot Rod Model A. I never put a dust shield on the turbo 350. This got me to wondering about if I should go...
View Article700R4 tranny wiring connections?
I got a 700r out of an 89 chevy pickup and put it in a rat rod i'm building and after reading a lot of different comments i don't know if it is computer controlled or not the plugin has three wires in...
View ArticleSBC Water Pumps
Merry Christmas to all my fellow Hot Rodders........ from the Great White North:)........I am wondering who can tell me the difference in the depth between a short water pump and a long water...
View ArticleDTM primer questions
I have been painting for almost 12 years so I am relatively still inexperienced and I have noticed a lot of suppliers really pushing the use of epoxy primers after blasting, stripping or any use over...
View Article