Clik here to view.
Back on the Road
well its been a while, but the old truck is back on the road. Attached Thumbnails     Â
View ArticleClik here to view.
"Car show in Santa Clarita,Ca."
Lots of awesome rides and good times. Mine won for best paint. Attached Thumbnails     Â
View ArticleClik here to view.
E350 Dually Rims
Hi all I hit some road debris last night and really destroyed my right rear outer rim... I pulled the wheel off this morning and started looking and googling for replacements. Not much info that I...
View ArticleT-350 not shifting into second gear
hey im having problems with my th350 automatic transmission which is not shifting into 2nd gear. i had just recently dropped the pan and reconnected the s-link going to he linkage and forgot to clean...
View ArticleChevy C10 HID Conversion
Anyone converted their 80s model truck headlights to HIDs? I have single headlamps and i know where to get the sealed beam conversion lenses aka euro lenses, but can anyone who has done this tell me...
View Articletruc won't start
I have a 1998 gmc 5.7 engine ,just installed new intake gasket, all went well but the truck will not start. It will start and run for about 10 seconds if i pour gas in throttle body. Ichecked fuel...
View ArticleClik here to view.
Spark Plug Reading Help?
I would like to get you guys oppinion on whats going on here. I have all the links on reading but still a little confused. The cylinder numbers are not correct on the cardboard. Engine is a mid 80's...
View ArticleNew member here from NYC
I've had a 1971 Monte Carlo for about 15 years now. It was given to me by my uncle when I was in need of a car for college (lucky me). It looks exactly like the one driven by Ace Ventura, lol. I didn't...
View Articlesbc shim head gasket leak
i have a sbc 350 with shim head gaskets & the passenger side head leaks a very little water like a drop then it stops at the back of the block. what could cause this?
View ArticlePiston stop without timing tab
Hey guys, i have a sbc 350 that I am trying to set up and tune. The problem is that i went to check the timing and the timing tab is missing. Im needing to find tdc but I have nothing to reference the...
View ArticleClik here to view.
Whats most cost effective in primer?
The state that my 59 rambler sits in currently, the front end is in black primer and there is some that was started on the drivers door (all done before I recived the car), there are panels where...
View ArticleHello Everyone!
I am new user and posting this thread to just introducing myself.I like cars and drive different types of vehicles.I will hope this forum is help me to learn new things.
View ArticleClik here to view.
sesame street song
one of these things is not like the others three of these things are kind of the same one of these things is not like the others. now it's time to play our game!:D
View ArticleOil psi and not so much psi
First and foremost I want to state that due to the rpm's I will be talking about we are diagnosing a boat engine. SBC 350, 2 bolt main, stock re ring and bearing kit. First and foremost, did I plasi...
View ArticleStarting Problem
I had put in a new starter and perhaps 3 months later it would not start when hot, but started when cold. I added a ground from frame to engine and a ground from starter to frame where the battery...
View Article1940 chevy key
Hello Gang I want to say thank you for all your help in the past.Now I am looking for a key blank for my 1940 chevy.The original key was made by Briggs and Stratton and is double cut and 1 1/4 long on...
View Articlenoise in eng
I have a 231buick v6 in my model a and I have what sounds like a lifter but no way to adjust valves has anybody had this kink of noise only does after warm around 50mph let off of gas noise stops dont...
View Article1987 gmc sierra ignition starter switch
Does anyone have a basic diagram of the wire placement for the switch or a drawing such as the earlier chevrolet wiring placement???
View ArticleMinnesota
Anyone here in the twin cities looking for practice on sewing up some interior for my project? Of course I'll pay! I just can't afford the shop prices right now? I figure it is worth a shot!
View Article