Vortec 6.0/LQ9 Build Idea
Hello everyone. I would like to pick everyones brain. Last year I got my blown 383 put together and running in my boat with a ton of help from this forum. I broke the snout off my crankshaft at the end...
View ArticleMaking my 63 GT Hawk breath.
What carburator(s) can I use on a Studebaker 289 v-8 engine that will fit the Studebaker 4 barrel manifold?
View Article350 engine stumbles,surges,hesitate at take
my 350 engine with edelbrock 1406 car hesitates and stumbles at take-off i can be cruising dwn street and if i punch it it will hesitate and have loss of power what can cause this problem. vacuum...
View Articlelooking for a shop in Dallas TX
Looking for a shop to get some quotes on a full interior for my 32 Ford Truck. Thanks Dan
View ArticleClik here to view.
32 Ford....rebuild
Hi all! My wife was given this little gem by her father last year for her birthday. He had some pretty severe health issue and didnt have the time to finish it off. We have now made the decision to go...
View ArticleSwitching cam shaft to fix fuel pump on 1988 Dodge Dakota
I have a 1988 Dodge Dakota, it came with a v6 but my friend's uncle who i bought it from had put what he said was a "boat engine" in the Dakota. It seems barely used and it appears to be a 318 to me, I...
View ArticleClik here to view.
500+HP 396 Bench Build Help. Cam? Pistons?
So I've Got this 1969 Camaro. It's a ready roller. All it needs is an engine/trans and shaft. It's a non power anything x11 car originally a banger so I don't feel bad about doing it wrong. Already has...
View ArticleClik here to view.
1939 olds rearend
does anybody know if i can get a newer center section for this rear end or you may call it a punkin where can i get brakes for it or wheel bearings thanks pkmosch
View ArticleClik here to view.
Second practice seat
hello, was able to weld and repair my practice seat, now trying to make the lower cover, Need advice on making pattern for lower front cover,?? I had many wrinkles on first practice seat, on front...
View ArticleClik here to view.
Getting to around 396cid using 880 block
To expand on my other thread about using a 400SBC with a roller cam in an L31 Vortec 350 application. What is the best way to get to around 396 cubic inches in a GEN 1 SBC? Anyone know of any good...
View ArticleSomething for Brian's wheelchair buddy!
Brian's a great guy for thinking about and takeing care of his disabled buddy, but here's something that ought to help out at the next car show they go to....
View Article1931 Model A serial number
HI, I'm new to this forum and just bought a 31 model A from a guy in florida. Drove it home to NC and went to get the title changed to my name and in my state. They(NC license dept) said i have to take...
View ArticleJust about to start my 52 F1 project
The truck has been in the dfamily since new looking to get info on IFS options and which is best. I think I'll put in a GM 350 with 700R4 and am looking for best places to get info.
View Article1996 Blazer electrical question
i know this isnt a hotrod but you guys have helped me out numerous times in the past so i figured i would give it a shot. my 1996 Blazer drains its battery non stop.. if i leave it hooked up the...
View ArticleIFS for a 52 F-1 truck
I have a 52 F-1 project truck that has been in my family since new. Looking for information on the best IFS to put in, cost, quality, ease of setup and durability. There seem to be options out there...
View ArticleClik here to view.
Cover for the ugly ford solenoid?
Does anyone make a nice cover for those ugly looking Ford solenoids? I have a smoothed firewall in my 55 Chev and had to hide that eyesore from view but it makes for a royal pain if you ever have to...
View ArticleHello
Hi guys: I'm new to this forum. Been hot rodding for over half a century. Still pick up some good tips and info from this forum :D
View Article#@*^&%$%#@!! flaring brake lines
Bought this %%$^# fancy Mastercool flaring tool. Cut up about three feet of %$&^% line trying to make a perfect @#$%^^$ flare....AIN't gonna happen. Back on it tomorrow!! Thanks for listening,...
View ArticleClik here to view.
pinion angle
I am new to the site and am in need of some help! I have a 57 3100 and I am installing a 79 Camaro rear end, my question is, does anyone know how many degrees of angle to set the pinion at keeping in...
View Article