Tuning Holley 750 Double Pumper, Need Help!
Hey everybody I have a sbc 355 10.5-1 Compression, .535 .550 Roller Cam, gets pulled to about 6200. The car is a drag car only gets trailered to the track. I went with a Holley 750 Double Pumper I know...
View ArticleHelp id chevy block
I have a chevy 350 block that I need to get a gasket set for, but, I dont know which one I need. I have seen two different sets, one for up to 80 and one for 81-85. The block, I was told, is a gm...
View Articledoor adjustment
Helping a friend adjust door on 88 monte after he changed hinges and the strike pin caught the door while trying to adj. it and cannot release the door . It clicked once and won't release . Any tricks...
View ArticleFord 5.0 or4.6
IM really thinking about a Ford Mustang and I can't deicide on a 5.0 or 4.6 I want to go to fuel injection and I don't know about them always been GM and I really like the 90s Mustang alot more then...
View Articlefresh 700R4, lost reverse only after 50 miles-
I hope someone may have an answer or suggestion, 1987 700R4 recent rebuild with all the good parts from PATC including new converter, built by GM transmission man with 25 + years experience. It has him...
View Article3 speed transmission on longer trips?
I am wondering how my 350th transmission would do on longer trips. I not wanting to across County more like 4 hours at the most. My trans has a shift kit and a stall tongue converter with the 3500...
View Articletee's 68 firebird
I just bought a 68 firebird shell, also bought a 1970 firbird engine (seperate). The engine is on a stand ready to get cleaned up. What should be the first step of my restoration???? First car I am...
View ArticleIt begins again
:thumbup: Hi- just getting back into some repairs with older vehicles. May be interesting. It looks like I will be helping swap out a tranny in my 1989 chevy 1500, various work on our 1989 cavalier...
View ArticleClik here to view.
Oil Filtration
As promised, I am reporting back after attending a NAPA/Wix product information seminar last night. Prior to attending, I have to admit that I was all about the "cut-aways" and "seeing is believing"...
View Articlehelp with proper cam selection
Got this 010 stamped block, two bolt. .030 over Trw piston, piston stamped trw 1801..... domed piston .100, from what I read a 11:1 piston with 64 CC heads. I have 3973497x heads.2.02, 76 CC. So I...
View Article57 chevy wiring
Can someone tell me if the 12 volt or 6 volt side of resistor goes to distributor?
View ArticleNeed help adjusting carb, idles high in part and too low in gear
I need help adjusting the edelbrock carb on my s10,it idles kinda high, around 1300-1400, and when in gear can drop low, to the point of stalling some times. I do not know anything about adjusting...
View Articleoil pan finish
Has anyone refinished a Canton oil pan to make it look original? If so what did you use? Thanks Duane
View ArticleNo start
Help I have a 64 Malibu that won't start I replace the starter thinking that was the problem but nothing now when I turn the ignition switch all my grounds get power can anyone help thanks
View ArticleA question about my 283
I have a 1967 Impala that I have been working on for a few years now, off and on. The previous owner told me that the engine was a 283 but I just looked up the suffix code and it reflects that of a...
View ArticleChevy 3100 steering
Hello I have put in an 350 engine in my 54 3100 pick up. no i have the Problem that the original steeringbox doesn`t fit anymore. does someone have an Idee how or wich steeringbox i can put in. i still...
View ArticleDry Sump Parts for BBC (OFFROAD)
Hello to all, i'm looking and reading about the system and i don't know all the parts i need, about the tank i will use 10-12qt tank. About pump i dont know what i need for my use 3 or 4 stage (or...
View ArticleNewbe jouning up
Just found this place totaly cool lots of info here.I am starting a Jag ifs & irs swap to a 60 F-1 Ford let the party begin.
View ArticleElectronic distributor
I'm thinking of buying a small cap electronic distributor from Whites Prerformance and was looking for some feed back on there products. I don't know if this is a post I can do or not. Thanks for the...
View Article