Fuel gauge and sending unit
I'm doing a 65 Ranchero. Have gauge pod from 66 'Stang and added gauges in lieu of all "idiot" lights. I tried using the original fuel sending unit but could not get a reading on the gauge. I ordered a...
View Articleoverheating 2002 chrysler 300
I have a 2002 chry. 300 the top radiator hose is very hot and the bottom hose is luke warm at best, radiator has been replaced in last couple days by a local shop, any ideas what i should look for? has...
View Article1954 Bel Air 2 door Sedan layin body on 22s
Well just joined the site a few days ago and figured id start posting the progress of my 54 with all who care to follow along. I found it in the back of a old uhaul truck about 4 months ago and after...
View Articlemodify
I am new to this forum, so I will say in advance thank you. My question is I have a 1971 ford 429 4V engine and transmission that I am installing in my short bed 1966 F100. What intake and carb set up...
View ArticleWhat Primer?
I have been working on the hood of my Z-28 and I ready to apply some primer to it and I am not sure what to get, the hood is the SMC type plastic or fiberglass that came on the 82 Z-28's. I bonded a...
View ArticleWhat year clear
Does anyone remember what year car companies switched from single stage to base/clear? I'm really interested in when GM/Chevy started using bc/cc. Thanks
View ArticleChassis Problem
Hello Everyone, I need help with material selection for my chassis. I am coilover mounting tabs and motor mounts from plate steel and I have a design but what thickness mild steel should I use. I was...
View Articleford f350 351w
my truck was ruuning fine , I checked the oil & coolante levels they were good . drove it for 15 mile than the valves started to rattle can't seem to figure it out ?
View ArticleClik here to view.
Sensor stuck in block...help!!!
Crankshaft sensor broke off in the engine block as pictured,it's made of plastic. Tried the pliers and made it worse any ideas? Attached Thumbnails Â
View ArticleMain jets and fuel economy relationship..??
I'm wondering if jetting down a bit could improve fuel economy.. at part throttle, where most of city driving is done, do the jets actually flow at full capacity? I say no way, so what would be the...
View Articlepaint stencils
hi, i am new here so will appreciate any input. i am getting ready to paint ss stripes on a 69 chevelle. i have a stencil kit and am worried about the glue on new base coat. what i am planning on doing...
View Articletransmission leaking
i have a 1985 chevy truck with a 700r4 transmission, i noticed today that transmission fluid was leaking out of the yoke off the transmission to the drive shaft. can yall tell me why it would leak and...
View ArticleWiring my engine bay from scratch need advice
Alright so for multiple reasons i had to start from scratch in the engine bay, battery/starter on different side, old harness in bad shape. The car is an 88 chevy monte carlo SS, the engine wiring...
View Article67 mustang straight 6
Hey guys. Iv got a question about older mustangs. Today I looked at a 67 mustang with a straight 6. A friend told me that when the floor pans started rusting on a mustang the car need a restore or the...
View Articleplumbing rear intake coolant ports
I have an air gap intake and a water neck spacer that I've plumbed to from back ports. My question is do I want it to bypass thermostat meaning thermostat below spacer with plumbed lines or should I...
View ArticleChevy 283 need lead additive?
Just got a 64 Impala with 74k miles and the original 283. Plan on keeping this as a cruiser. Do I need to add a lead additive to the gas when I fill the tank and why or why not.
View Articlehead upgrade questions
im wondering what would be a good head to get for my chevy 350. i have an edelbrock performer intake, edelbrock 600 cfm 4 barrel, bored .30 over, .268 cam . im trying to get better street performance...
View Articlebumper lengths
I have been debating on roll pans or different bumpers for my '62 Ranchero is there a way to seach the net for bumper lengths?I tried to calculate using the tailgate and the depth of the rear...
View Articleinexspensive ,cheap to buy distributers
As of late I've been reading a lot about hei dizzys.I bought a $60-$75 one at Goodguys Columbus,3-5 years ago.It was a nice looking piece,machined casting,red cap.It ran fine until this spring.It would...
View Article