79 F350 400M Swap to 300 inline
I want to know if anyone has done the 400M to 300 inline swap with C6 and what to look out for. I know that the Canadian block (grey block) was a POS, but the blue block was one of the best built. No...
View ArticleHow do I correct my Chevelle's speedometer?
how do I correct my speedo, chevelle, with 350 ,400 trans and 373 gears ,255-15 tires .reads faster then im going
View Articlerestore of my 1965 C10
I am looking for the best down to metal primer and painting tricks for my 1965 C10 stepside truck:confused:
View ArticleGreetings from Greece
:welcome:Hello guys! Nice to join you on this forum! Regards, Alexander
View ArticleBuilding a 307 sbc with 471 Weiand blower.
:welcome: So here is what I have. 307 sbc seized. I think its bearing. Wasn't catastrophic failure. A gradual knocking turned into a not so gradual knocking. Its locked up and dead. 471 Blower with...
View ArticleHi from New Zealand
Hi its Matt here. I live in New Zealand and we have a very healthy Hot Rodding and Dragracing scene here in NZ. I have a T-Bucket that I have owned since 1984 when I was a young fella and its had...
View Articleglad to be aboard
Hya all-accidently found the site researching epoxy-having recently attempting to repair a massive softwood consevatory- The warm summer we are having led me to try the versatlity of mainly fibreglass...
View ArticleFuel tank filler cap
Howdy, I have a question about the gas tank filler cap..... I have a Ford 5.0L EFI engine in my 65 Mustang and need to know, do I keep the vented cap or do I need to change to a more modern cap? Jerry
View Articleshould I prime the engine??
OK I have several trucks that I do not drive very often. I crank them up several times a year. I have a bullet proof 1990 f150 5.0l that does get called into action occasionally. So it will go from...
View Article65 Chevy truck 12 bolt rear end
I'll be dropping my truck off sometime this week at a friends house.he is putting a posi unit in and some 3.73 gears in the 12 bolts.I asked for 4.11 gears but he was out of them unfortunately .im...
View ArticleNew to site 1964Chevy II
Hey all I have a 1964 Chevy II Nova 400 hardtop . I purchased it with the original 283 and mostly all original survivor with a few upgrades ex: turbo 359 with shift kit. I have since in the past three...
View ArticleLooking for rear and trans for 1964 Chevy Nova anyone help?
I just finished my new crate GM 350 and need a new rear and want to swap to a 5 speed manual or OD auto trans does anyone have any Leeds I just can not afford new trans and rear unfortunately I work...
View Articleexaust is to loud,legal wise..
For starters $ is tight but I have warmed over sbc 355 with headers into 3" dual exaust dumping at the axl I have original 40 series flowies and 2.5" cats 3" was way more expensive it was obcenely loud...
View Article65 Chevy truck 12 bolt rear end
I'll be dropping my truck off sometime this week at a friends house.he is putting a posi unit in and some 3.73 gears in the 12 bolts.I asked for 4.11 gears but he was out of them unfortunately .im...
View Articlehow dumb & lucky can ya get ???
Did somethin reallydumb last nite.A local farmer that builds & competes in truckpulls had a benefit pull & mud drag last nite to help a local family that is havin a hard time.I went just to...
View ArticleLower cross-shafts for Porterbuilt control arms
I noticed that Porterbuilt control arms appear to come with only upper cross shafts. Does anyone know if they specify using the stock cross shafts for lower arms. Thanks
View ArticleIs there a simple way to test for power to transmission and solenoids ?
Hi all its on a 2002 Suburban 5.3 V8 with a 4l60e while trying to find out if my tranny has poer or not, to solve my gear shirting problem does anyone know if there is a simply way to test power to...
View Articleno 2nd or 4th on 4l60e
So iv got a 2000 chevy blazer 4x4 with a 4.3 and 4l60e that wont shift into 2nd or 4th gear. you can rev it up in 1st, let off the gas and it will go into 3. i checked the 2-4 servo, no problems there....
View Article32 desoto front axle
if theres anyone who can help me out with this issue please do .......... my issue is ....... i bought a straight front axle from a 32 desoto with spindles . no backing plates ..... i need either disc...
View Article